Audio

The Presence 10: DIY Atmos Height Speakers for About $320 Each

High-efficiency height speakers like the JTR 110 run about $1,300 each. I built an angled Celestion FTX1025 coaxial speaker for about $320 each in parts instead.

October 29, 2026 6 min read Nick Wilbur
Pair of Presence 10 angled DIY surround and height speakers

I needed Atmos and presence speakers for my theater, and I wanted high-efficiency ones like JTR or Ascendo make. A JTR 110 is about $1,300 per speaker. So I set out to build something for around $300 each, using the same basic idea those companies use: a 10-inch coaxial pro driver, here the 96 dB Celestion FTX1025, in an angled box for the wall or ceiling.

Celestion sent me the speakers for this build. The thoughts and opinions are mine alone.

Some links on this page are affiliate links (Parts Express and Amazon). If you buy through them, Toid may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.

Get the Presence 10 Plans

Watch the video · 10 min

Watch the Presence 10 build

Four speakers for the price of one

I looked hard at the high-efficiency height speakers from JTR and Ascendo, and they are really expensive. So what if we could DIY something a lot cheaper? If you could build four DIY speakers for the price of just one JTR, that would be pretty neat. That's exactly what this build is.

A lot of companies make these presence speakers right now, and they all use the same basic design. They take a 10-inch PA speaker that's actually a coaxial driver: a one-inch compression driver mounted on the back fires the high frequencies out through the middle, and the woofer part gives you your low end.

Presence 10 DIY Atmos height speaker with Celestion FTX1025 coaxial driver
The Presence 10 build video thumbnail.

One driver does the whole job

I wanted a driver better than the basic ones out there, something with a little less distortion and a better sound. That's how I came across the Celestion FTX1025. It's 96 dB sensitive, which makes it perfect for a project like this, and the driver itself only costs about $260. I wanted to land right around $300 per speaker, so it fit the budget.

Because the compression driver is mounted directly on the rear of the woofer, the whole thing stays shallow. That minimizes the depth of the speaker, and it shaped how I designed the box.

Built at an angle on purpose

I designed it with a slanted look so you can use these as rear speakers or as on-ceiling Atmos-style speakers. At this price you could build eight of them for about the cost of one pair of something equivalent that's mass produced.

I worked out the enclosure shape in a box design program and sent it to the CNC. You don't need a CNC. I only used one because I put a brand-new motor on my table saw and now its tilt function doesn't work. In reality, the CNC took considerably longer than a table saw that could make angle cuts would have.

Seven pieces, one glue-up

Because of the unique shape, the whole box glues up in one pass, with seven pieces instead of the usual six. One angled piece gave me a lot of trouble staying at the right angle, so I cut a spare piece exactly the same height as the rear and used it to prop that panel up during the glue-up. It was temporary and came out once the glue was done.

Clamping an angled box has its own challenges, so here are the tricks that helped me (if you have better ideas, leave them in the comments on the video):

  • Put some paper towel down so the wood doesn't get stuck to your clamping blocks.
  • Clamp the seam tight, because as the glue expands it can push the seam up.
  • Slip blocks underneath and clamp them on to hold everything in place.
  • Lay a bar across so you can put pressure on the clamp and the bottom of the box at the same time. That squeezes the whole thing together.

T-nuts keep the driver in, even upside down

Before painting, I had to decide how to mount the drivers. I could have used plain screws, but I went with T-nuts. A T-nut clamps onto the inside of the panel and gives the screw something solid to bite into, so you get pressure from both the back and the front. That matters a lot if you hang these upside down.

T-nuts hold the driver in the cabinet; they don't hold the cabinet up. If you mount these overhead, use a bracket rated well above the speaker's weight, screw it into ceiling joists (not drywall or drywall anchors), add a safety cable to a joist, and check your local building code. If you're not sure, have a pro install them.

Once the glue dried, the clamps came off and the boxes got sanded. For the finish I used ExoHyde from Parts Express with its special textured roller to get that unique textured look. Unfortunately, the footage of that step went missing.

Pair of Presence 10 angled DIY surround and height speakers
The finished Presence 10s.

A crossover that knows where it lives

The crossover is my favorite part, because it takes two raw drivers and makes them into something special. What makes this one different is that the crossover is tuned for where it's mounted (6:22). Normally I design to an anechoic response, because I don't know where someone will put the speaker. Here I do: on the wall or on the ceiling.

That changes the final response because of boundary reinforcement. Usually low-frequency waves wrap around the cabinet and get lost behind the speaker. On a wall or ceiling, they bounce off the surface and come back toward the listener. That works in our favor: it lets the speaker cross over between 80 and 120 Hz, which is exactly what I want from a rear surround or Atmos-style speaker. The shape of the speaker improved the linearity, too.

The high end had a rising response, so I designed a custom filter to bring it back down. In the end, the response is about plus or minus 2.5 dB, which is really good for a speaker of this design, especially at this price.

The verdict from the ceiling

I am absolutely blown away by what these deliver for what they are designed for. This is exactly what I needed to complete my Atmos setup with high-efficiency rears, and I couldn't be happier.

If you're not into DIY, or you don't think a project like this is for you, take a look at JTR or Ascendo. They make fantastic speakers. But if you are into DIY and want to save some money, see whether these fit your needs.

What one costs and how big it is

The Presence 10 plans page puts the parts at approximately $320 per speaker, and each finished cabinet is 14.5 inches tall, 14 inches wide and 9.25 inches deep. Prices change, check the current price.

Build your own

You don't need to know how to design this crossover yourself: it's in the plans, along with the cabinet dimensions, enclosure angles, wiring and parts information. You can also browse all of my DIY home theater speaker plans.

Get the Presence 10 Plans

Filling out the rest of the system? See the Audience 212 for the front stage and the Cinema 10 for a thin, sensitive surround or center.

Parts Used and Mentioned

Here's what I used in the build, plus a few items mentioned in the video description. Each row says which. Prices change, check the current price.

Some links below are affiliate links. Toid may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.

Item Used or mentioned Link
Celestion FTX1025 10" coaxial driver Used. Celestion sent me the speakers. Parts Express
Neutrik NL4MPR Speakon chassis mount Used. Parts Express
Neutrik NL4FC Speakon 4-pole cable plug Recommended. The 4-pole plug that mates with the NL4MPR jack. Neutrik has discontinued the NL4FC; its direct successors are the NL4FXX-W-S (for 6 to 12 mm cable) and the NL4FXX-W-L (for 10 to 16 mm cable). Parts Express (NL4FXX-W-S)
T-nuts Used to mount the drivers. No link
ExoHyde textured cabinet coating Used for the finish. Parts Express
foamPRO textured roller refills Used with the ExoHyde. Parts Express
foamPRO textured roller handle Used with the ExoHyde. Parts Express
Titebond II wood glue Used for the one-pass glue-up. Amazon
Glue spreader Used. Amazon
Acousta-Stuf polyfill Mentioned: listed in the video description's parts list. Parts Express
Terminal block Mentioned: listed in the video description's parts list. Amazon
Bosch 1617 router Mentioned: the non-CNC route. I used a CNC because my table saw's tilt was broken. Amazon
Template bit Mentioned: the non-CNC route. Amazon

Prices change, check the current price.