Audio

Why I Rarely Offset a Tweeter (and When I Do)

Offset tweeter placement can cut edge diffraction, but only when the distances to the edges change, and it costs a mirror-image off-axis response. Why I keep most tweeters centered.

November 13, 2026 5 min read Nick Wilbur
Red bookshelf speaker with its tweeter offset toward the top corner above the woofer, with a red arrow and the words Don't Do This

Why is the tweeter on an Overnight Sensations offset, when so many other speakers keep it dead center? Is it just looks, or is there a difference in sound quality? Some of it does come down to aesthetics, but there are real reasons to offset a tweeter. I just don't do it very often, and here's why.

Some links on this page are affiliate links (Parts Express). If you buy through them, Toid may earn a commission at no extra cost to you.

Browse my DIY speaker plans

Watch the tweeter placement talk · 9 min

Offset or centered tweeter

Offset or centered

This came up on Audio DIYgest, the show I do live on Wednesdays, and my co-host and I went back and forth on it. The question was simple: offset or centered, and does it matter? My answer was that there are actual reasons to offset a tweeter, but I only do it when a centered tweeter would leave the same distance to the top and to the sides. I try to avoid having the same distance, and the reason is diffraction.

Here's the example I gave. If the distance to the top is two inches and the distance to the side is three inches, I keep the tweeter centered. Those distances are already different, so there's no reason to move it.

The short version of diffraction

I've covered edge diffraction in more depth in my post on the best speaker box shape, so here's just the part that matters for placement. The distance from the tweeter to the edge of the baffle corresponds to a wavelength, and so to a frequency. When the sound reaches that edge, long enough wavelengths wrap around the speaker and short enough ones just carry on forward. At the right wavelength, though, it comes back to the listener or the microphone out of phase with the on-axis sound, and that creates dips and peaks in the frequency response. With some basic math, the distance and the speed of sound tell you exactly which frequency that will land on, and then it can be measured to prove it.

So every time two edges are the same distance from the center of the tweeter, the diffraction lands at the same spot on the graph. On the stream, we put it like this: one crazy kid in the house is bad, two is worse. The worst case would be a cube with the tweeter right in the center, or a circle, because the distance is the same all the way around.

The principle: an offset only helps if the distances change

The biggest reason to offset a tweeter is to cut down on diffraction. But offsetting only makes sense with a reason behind it. I've seen too many people offset a tweeter and still put it the same distance from the top and the side, because it looks good. That gets rid of any of the reasoning behind offsetting it for sound performance. All it does is move the point where the diffraction happens.

It's the same thing I say when I list the driver placement mistakes I see: offsetting drivers can sometimes help reduce baffle diffraction, but only if it's done intentionally and with supporting measurements, not just because it looks cool. And if a trusted design already has its drivers placed, I don't change them.

What an offset costs

This is the part people skip. With the tweeter centered, the off-axis response is a mirror image: 45 degrees to the right looks just like 45 degrees to the left. That's the reason most people center their tweeter. With an offset tweeter, going toward the tweeter side gives a different response than going away from it.

My co-host pointed out that it also changes how a speaker gets measured. Off-axis measurements on a commercial speaker usually go in one direction. With an offset tweeter, they really need to go both ways, all the way around.

So for me, if I'm going to offset a tweeter, it's typically only on near field monitors. I don't like the idea of offsetting tweeters on far field speakers. That's a personal decision. Near field, the off-axis response doesn't matter as much as it does with far field speakers. And outside of near field monitors, one of the points we ended on was that there are other ways to deal with diffraction that are probably better.

Offset vs centered, as I see it

  • Centered, top and side distances different: what I usually build. Mirror-image off-axis response, and the diffraction is already spread out.
  • Centered, top and sides the same: the one case where I'd consider an offset.
  • Offset, but the same distance to the top and side: mostly for looks. It just moves the diffraction.
  • Offset with different distances on every edge: spreads the diffraction out, at the cost of an uneven off-axis response. For me, near field only.
  • Distances that are multiples of each other, like 6 and 12 inches: something we said to avoid when doing the math.

Where I changed my own design

My first home theater speakers were based on the Klipsch KL650s, and on version one the tweeter was offset on the woofers. That was a design I picked up from the original Klipsch and just wanted to replicate. When I came back with the Cinema 6, the waveguide moved to the center of the two woofers, and the single port became two ports, one on either side of the woofers. All of that was to help with off-axis response. With the waveguide centered on the woofers, the response is much more even, which gives a lot more flexibility in where the speakers can be placed.

The trade-off, and the limit

So this isn't only about looks. It's about trade-offs. An offset can help diffraction, but it gives up the symmetrical off-axis response, which is exactly what I want in a home theater or far field speaker. A speaker with a centered tweeter will still have diffraction on both sides and on the top, so centering isn't free either. That's why I care about the top and side distances being different.

The limit here is that this was a conversation, not a measurement. The reasoning is something anyone can measure and prove, but in this video we talked through it rather than putting a pair of offset and centered baffles on the same test.

See where it led

For the full look at edge diffraction, including the off-center tweeter that ended up no different from a centered one, read the best shape for a speaker. And for a home theater speaker I built after the Cinema 6, see the Cinema 10.

Keep building: The best shape for a speaker (and the ones to run from) · The Cinema 10: a Klipsch KPT-inspired theater speaker · I designed the Epic HiFi, then I built it · all my DIY projects

Parts Used and Mentioned

Here's what I mentioned, with the link I have.

Some links below are affiliate links. Toid may earn a commission at no extra cost to you.

Item Mentioned Link
Overnight Sensations MT speaker kit (pair) Mentioned: the offset-tweeter example the question started with. Parts Express